Monday, October 23, 2023

Rotate spring tension set correctly, tab setting sliders loosened as I continue to work on the 1053 console printer

ROTATE SPRING TENSION CORRECTED

I managed to find a solution to the conflict between lights, my eyes and the tools, so that I could see and maneuver the rotate spring and its detent. I relieved tension on the spring and then carefully added it back in until I got to the desired range of rotate tape tension. 

The tension is measured by setting up the machine with the type element (ball) on the lower case side, commanding a character with a -5 rotation and hand cranking this until the rotate pulley on the right is just about to hit a stop pad that limits the pulley lever arm travel. With this condition set up, an IBM spring scale pushes against the pulley lever arm and measures the force required to move the arm outwards. 

This force is the target spring tension of 1 7/8 to 2 1/2 pounds. I found a setting that produced 2 1/4 pounds of force, right in the desired range. To verify this is good, we also check at +5 rotate character from the upper case side of the ball.

Tripping a solenoid on the side of the machine causes the pulley lever arm to move outwards to the right, which pulls the ball around so that the upper case side faces the platen and paper. The +5 rotate character was triggered and hand cranked to the point where I could again measure the force on the pulley lever arm. We still had 2 1/4 pounds of force, confirming that the rotate tension setting is correct. 

TAB SETTING SLIDER CORROSION

The tab setting sliders are discs that fit inside slits on the long tab cylinder, one slit per column that the carrier can reach. The disc rotates so that the two projections which stick outside of the tab cylinder diameter are either rotated backwards to the rear of the typewriter or partly forward. The forward position puts a projection right in line with the escapement mechanism on the carrier. The carrier strikes the projection and releases the latched tab condition allowing the escapement pawl to enter the rack and stop the carrier at this position. 

Quite a bit of corrosion has occurred inside the slits and on the faces of the discs, which froze some in place and made them all very hard to rotate. Using my clock oil and patiently moving each one back and forth many times, I got most of them to move freely. I still have a few that are stiff but with time and more manipulation I expect them to all work properly.

I verified the gang clear function, where as the carrier is pulled right to left during a carrier return operation, if the Tab Clear lever is activated simultaneously, a wedge on the front of the carrier will force up any tab discs that are rotated into the 'set' position. This clears all tabs in one operation, instead of requiring the user to repetitively tab to each set position and then move the Tab Clear lever. 

ADJUSTING STOPS ON WHIFFLETREE LINKAGES

IBM implemented a mechanism called Whiffletree Linkage to select the amount of movement of the tilt and the rotate tapes required to move the ball to print the intended character  The heart of this mechanism is different lengths from pivot points to the activation levers for each 'bit' of selection. 

Tilt is easier to explain since it has only four possible positions. A horizontal bar has two levers dangling from its ends. One is twice as far from the horizontal bar pivot as the other lever. Thus, pulling down on the far lever produces one unit of movement, pulling down on the nearer lever creates exactly twice as much movement of the tape, and pulling both down adds together the movement to pull the tape three times as much as the far lever alone. 

https://www.youtube.com/watch?v=G_SC7oWL78A

Rotate requires five positions in one direction and five positions in the other plus no rotation, thus eleven possible rotary positions of the ball. The mechanism has a negative rotation link which reverses the direction of the movement plus four levers to select one of the six positions in a direction from no movement to rotating five positions. 

As the typewriter sits right now, it rotates the ball less than one character position so that a +5 or -5 character request only produces a movement to the +4 or -4 character on the actual ball. I will be working through the adjustments that must be made, in the proper sequence, to cause the ball to rotate properly.

The first sets of adjustments are setting the rotate spring tension and setting the left side rotate pulley lever to be exactly vertical when the ball is set to the zero rotation position. Immediately afterwards, I had to deal with the failure of the vertically hanging levers from the Whiffletree to restore themselves under the bail that will pull the levers which select the amount of tilt or rotate movement. 

I don't know if the improper position of the levers is part of the inadequate rotation of the ball but the adjustment needs to be made so that they do restore. When a lever is selected by the solenoid, it is pulled away from the bail so that that lever is NOT pulled down. It should restore under the bail so that the next request for a character where the solenoid is not driven should have the lever pulled down. Failure to restore may result in mis-selection of print characters at speed, thus this must be corrected.

Metal tabs above the top pivot of the vertical levers are bent downwards until the bottom end of the lever will restore under the bail. These are called stops. There is no direct way to reach and bend those tabs while the Whiffletree mechanism is in place, but I don't want to disassemble everything. I will figure out a method to adjust the stops and do it. 

CR DRUM SLIPPING AND RELEASING SOME CORD TENSION

I noticed that at the end of the day today, the transport pulley has moved outwards away from the scribed line, indicating insufficient tab cord tension. It seems obvious that the CR drum screws are not holding the drum on the shaft sufficiently, I was worried about the amount of torque I had to apply last time and it still didn't hold. 

My guess is that sludge is in the threads of the drum hole and on the screws. I will try to clean them out thoroughly and reinstall the drum. I may have to use some Loctite Threadlocker to hold them in place so they don't loosen up on their own, but only when I am certain that the screws are holding the drum firmly to the shaft. 


Sunday, October 22, 2023

Tab and carrier return cords installed at proper tension

DRUM ADJUSTED UNTIL THE TRANSPORT PULLEY POSITION WAS AT LINE

It took a few more iterations than I expected, in part because the drum would slip if I didn't really tighten the screws down quite firmly. It felt as if I was on the edge of material failure on the screw when I attained the final tightness that left the transport pulley at the target position .

Left edge of slider right on scribed line

THE TAB POSITION SLIDERS WERE GUMMED SOLIDLY IN PLACE

Tab positions are controlled by a long cylinder running from left to right behind the carrier rails, with a rotating slider for each of the columns across the page. Moving the slider in one direction allowed the carrier to sail past it unimpeded during a tab operation, while placing the slider in the other direction would trip a latch on the carrier to stop the movement at this column. 

Pushing the Tab Set or Tab Clear button on a typewriter (an up/down toggle switch on the 1053), causes the slider at the current column position to be moved to either the set or the clear position. As a convenience, when doing a carrier return, if the Tab Clear is held down then the carrier resets the sliders on all columns as it returns past them. 

These sliders were stuck in place by solidified lubricants, requiring me to flush them out with clock oil and work the sliders back and forth until they moved freely. With that done, the tab operation could work as intended, moving the carrier right to the next column that had its slider set. 

Tab sliders move to set or clear positions

ESCAPEMENT MECHANISM CHECKED FOR PROPER OPERATION

The rear of the carrier has a set of levers that are connected in a complex way. Two of them have pawls that engage in the teeth of their associated racks.  Another will force both of the pawls out during the carrier return and the tab movements. 

The space rack is what holds the carrier at its current column against the pressure of the mainspring and tab cord seeking to pull it rightward. The escapement lever can pivot its pawl out of the rack, the carrier begins moving, and then a spring pulls the pawl back into the next tooth of the rack. This moves the carrier a single column to the right. 

This lever is moved by a long bar running just behind the carrier, which pivots during the end of the a character print cycle to cause a one column advance. It is also pivoted by the operation of one of the two operation clutches, when the space button is pushed on the front of the 1053 or when the space solenoid is activated. The button or solenoid trips a clutch, rotating a cam one half rotation during which the cam moves levers that, in the case of a space function, pivots that bar that moves the escapement lever.

A second rack is offset a bit from the first and has pawls on the backspace lever that insert into the rack. If the backspace solenoid is activated, it trips the same clutch as was used for space, but the cam moves levers that engage the backspace pawl and drive the carrier back one column. The escapement pawl pops out of its rack and into the tooth one position behind. 

Finally, the escapement and backspace pawls are held out of the teeth of their racks during the long movement operations, tab or return. Another pivoting bar behind the carrier moves those levers out of the way. In the case of a tab operation, whose distance is determined only the the sliders that are in the set position, some levers and springs hold the pawls locked out of the teeth but when a set slider strikes a small projection on the carrier it releases the pawls to lock the carrier at that position. 

The escapement and backspace pawls plus tab latch levers

Some success with tab and carrier return cord installation

USING THE NEW METHOD OF ROTATING THE CARRIER RETURN DRUM A BIT

With the carrier return function engaged so that the drum shaft won't turn on its own, the two screws holding the CR drum to the shaft are loosened and the drum rotated enough to add a bit less than a half an inch to the net cord length. The cord would then fit over the spring loaded pulley (transport pulley) and the pulley sits at the scribed line  on the assembly to indicate proper tension. 

LOOSENED AND THEN REMOVED SCREWS BUT COULDN'T BUDGE DRUM

I loosened the two screws but the drum wouldn't turn on the shaft with hand pressure. I backed out the screws further and eventually they came fully out of the drum yet it wouldn't budge. 

Drum with screws removed

Removed screws

TOOK APART DONOR MACHINE TO CHECK THE SHAFT FOR FLAT SPOTS

The from (tab) drum uses a single setscrew that tightens against a flat spot on the common shaft, but the presence of two screws on the CR drum suggested it did not have a flat spot. However, with no movement of the drum, I considered the possibility that my speculation was wrong. 

I therefore removed the entire shaft and drum assembly from the parts donor Selectric I had acquired and got the drum off to examine the shaft. The drum didn't slide off but when I used vise grips to turn it relative to the shaft, I began to turn. Apparently it was just grime that had hardened to stop the drum from turning. 

Studying shaft from donor typewriter

USING TOOLS TO START THE CR DRUM ROTATING

Once I was comfortable that this should and would rotate freely around the shaft, I carefully applied some tools to the metal hub of the CR drum and worked on moving the drum. I did get it to move, slowly at first and then with less pressure as I increased the distance it had moved. 

This allowed me to move the carrier and even up the pressure on the tab and CR cords. The cord could then be pulled over the transport (spring loaded) pulley with the assembly just about at the scribed line. I tried moving the carrier in both carrier return and tab directions with hand cranking and it appeared to be working correctly. Clearly this method is the key to getting everything perfect.

LENGTH OF CORDS AND TENSION IS NOT PERFECT YET

Because I hadn't replaced and tightened the screws while I was checking the cord tension and positioning, the force of movement rotated the CR drum a bit more resulting in the transport pulley sitting too far out from the frame. There is not quite enough tension now.

Cord is a bit too loose

All this means, however, is that I have to move the CR drum back in the other direction, tighten down the screws and then verify the tension. It may need a bit of iteration but I am certain to get the tension just right using the new method. That will be my next task when I return to the workshop, then I can move on to setting the rotate spring to its proper tension. 


Friday, October 20, 2023

Found a new approach to get the tab/return cord tension adjusted

TENSION IN THE COMBINED TAB AND CARRIER RETURN CORDS

These cords hook onto the carrier of the typewriter and run in opposite directions, providing the force to move the carrier left or right. The reverse direction around pulleys on the sides of the machine and then are wound around drums. These drums are on the same shaft hooked to the mainspring. 

They hook onto attachment points on the carrier and at the start of spiral grooves on each drum. As the mainspring shaft rotates, one drum winds in cord while the other drum plays out the same amount. Turning one direction, the carrier is pulled to the left by winding on the carrier return drum while cord is released by the tab drum. The other direction winds the tab cord on its drum while the carrier return drum releases some of the carrier return cord.

One of the pulleys on the side of the machine is spring loaded, in order to maintain a target tension on the cords. A scribed line on that assembly marks the ideal position of the spring loaded pulley when the cords are at the proper tension. 

To keep the cord from popping off its drum, each drum must have about one wind of cord when the carrier is at its extreme position - left side of the machine for the tab drum and right side for the carrier return drum. With the cords attached to the drums with the desired one wind of cord on one and the other drum wrapped as many turns as needed to keep that cord tight, the tab cord should fit around the spring loaded pulley and sit at the scribed line.

MY ATTACHMENT LEAVES THE TAB CORD TOO SHORT

The process of installing the cords puts the carrier return cord the carrier, routes it around pulleys on the left side of the machine and hooks it to the attachment point  of the CR drum. Latching in a carrier return operation causes the CR drum to wind up the cord as you manually crank the machine, pulling the carrier to the left side of the machine. 

Each spiral of the drum pulls the cord by a specific amount (pi times the diameter of the bottom of the spiral groove on the drum) until carrier reaches the left margin (side) of the machine. When the carrier is at the far right margin/side of the machine, there would still be a bit of cord wound around the CR drum thus the cord won't pop off.

Next the tab cord is hooked to the attachment point of the tab drum, wound around it once and then routed around the side pulleys until it is hooked to the right side of the carrier. Each turn of the tab drum pulls the cords the same amount, pi times the diameter of the groove bottom on the drum spiral. 

What this means is that the attachment point position of the two drums determines the start of the cord and then each rotation of a drum pulls up pi times the groove diameter of cord. The attachment point position on the drum can be anywhere in a 360 degree rotation, thus the angle where the attachment point sits when the cord is attached can shorten the cord by up to pi*D. 

If the drum's spiral groove bottom is one inch in diameter, to simplify the math, then the cord length is from 0 up to 3.1415" shorter, determined by the angle of that attachment point. This is important since the cords don't have a fixed net length, it is determined by the attachment point angles. 

When I installed the two cords per the various installation instructions, I end up with the tab cord net length too short by about 3/4 of an inch or it is too long when hooked to the tab drum attachment point without any turns wound on the drum as the carrier is all the way on the left side of the typewriter. 

I can compensate for the overly long cord by tying knots but the lack of any winds on the tab drum results in the cord popping off during a carrier return operation. Thus I need one wind of the cord on the drum, producing the deficit of about 3/4 inch. 

READ MANY IBM ADJUSTMENT MANUALS BUT ONLY ONE MENTIONED THIS KEY TIP

I have several manuals describing the adjustment procedures for the I/O Selectric (and regular Selectric). Every one, including the documents that came with the IBM 1130 system, skip this key adjustment. When they talk about adjusting cord tension/length they only cite the ability to tie knots in the cord to shorten it. I then found one manual online with this figure that offered a hint.

This does not show the two screws for adjustment, nor mention rotation of the drum. The right hand transport pulley is the one that I call the spring loaded pulley. In retrospect, I see that this comment means intends the mechanic to loosen the two screws on the CR drum, turn it to set the position of the 'transport pulley', then tighten them up. 

Setting a  new rotary angle for the CR drum effectively can shorten that cord by up to 3.1415" but the target is to shorten it by the missing 3/4" which simultaneously moves the attachment point of the tab drum enough to have one wind of cord on the drum with sufficient space to fit onto the spring loaded pulley. 

CAUTION ON THE TAB DRUM WITH ITS ONE SETSCREW

The front drum (tab drum) is affixed to the shaft with a single small setscrew. The documents all warn that this setscrew fits onto a flattened section of the shaft thus you can't turn the tab drum to adjust the cord length. It only fits at one rotary position relative to the shaft. 

Tab drum

Otherwise this would be the obvious pulley to try to adjust, as it is the tab cord whose length over the spring loaded pulley is the subject of adjustment. Due to its construction, however, that drum cannot be rotated around the shaft. Instead we have to adjust the CR drum, which changes where the tab drum stops when the carrier is at the full left position. 

TWIN SCREWS ON THE CARRIER DRUM ALLOW IT TO BE ADJUSTED WITH WRENCHES

The rear (carrier return) drum has two screws placed at ninety degree positions around the shaft, with nut heads to make it easy to turn with a wrench or nutdriver. These anchor the drum to the shaft and thus don't depend on flat spots as the tab drum does. 

Different model drum 

I couldn't find a good picture of the CR drum, which looks very much like the tab drum above but has the nut head screws I mentioned. This picture from a different Selectric model has setscrews instead of the nut head type but you can see the same basic adjustment scheme with two screws at ninety degree angles. 

That is what the terse comment in the IBM manual above refers to when it says to 'adjust carrier return drum until . . .  right hand transport pulley is clearing side frame . . .' as we want to cause the tab drum attach point to have moved. 

THE MODIFIED PROCEDURE THAT I NEED TO IMPLEMENT

The mainspring can remain wound up, under tension, because the gears and clutches at the front of the machine hold the tab drum from movement when carrier return is activated, thus I can loosen the carrier return drum without the spring spinning around.

Loosening the two screws with a wrench, I can spin the carrier return drum on its shaft, letting out a bit of cord until the tab cord side would be in the approximate position to sit at the scribed line of the spring loaded pulley that we wish it to attain. Once tightened up, I can pull the tab cord over the spring loaded pulley and verify the cord tension. 

Wednesday, October 18, 2023

Getting close on tab cord and rotate spring tasks

JUST A HAIR TOO SHORT FOR SUCCESS WITH THE TAB/CR CORDS

I used the method from Phoenix Typewriters I watched on YouTube and carefully loaded the cords and wound the mainspring. When it was done I was left with a cord attached but too tight to fit over the spring loaded pulley on the right side. It is just a touch too short - if I had perhaps 3/8" to 1/2" more length then the spring loaded pulley would sit at the scribed line that shows perfect positioning. 

Tab cord attached with one loop around pulley

Cord too tight to fit on spring loaded pulley in normal position

This is the result with one loop wound around the tab pulley. I can add knots to shorten the tab cord but then it attaches without any loops around the tab pulley; that is likely to result in the cord popping off the pulley when the carrier reaches the left margin. 

Will study this carefully and see if I can figure out a fix that doesn't require manufacturing a new set of tab and carrier return cords to get the correct lengths. 

LOCATED SPOT TO LESSEN ROTATE SPRINT TENSION

Finally I found an opening where I could see the two objects I need to manipulate to release some rotate spring tension. The rotate spring is a disk shape that sits at the bottom of the shaft which holds the typeball. There are notches around the periphery of the spring and a detent that extends out to catch the nearest notch. This keeps the spring housing from rotating.

To add tension, a screwdriver or hook pulls the spring housing around, with one notch slipping out of the detent and the next notch clicking into place. To release, however, one has to simultaneously manipulate both the detent and a notch on the spring housing.

I will have to pull the detent away from the spring housing disk, freeing the notch, while the other hand controls the unwinding of the housing so that it only moves a bit before I release the detect. Then, the detent will have clicked into the notch prior to the one it had been holding. I do this repetitively until I measure correct spring tension of 2 to 2 1/2 pounds force at the rotate arm. 

THREE REQUIREMENTS FIGHTING FOR ONE SPOT

The gap through which I can see the rotate spring housing and the detent is small. The parts I have to touch are a bit deep inside the gap as well. This triggers the battle among three necessities to do this work. First, I need a bright light at the proper angle to shine down and illuminate the parts to be manipulated. Second, my eyes have to be over the gap so that I can see the parts. Third, two tools have to fit into the gap, one to control left to right movement of a notch on the spring housing and another to move the detent forwards to release it. These have to be fairly small tools because of the limited space.

My challenge is the conflict  between those three elements. The light has to be at the correct angle to illuminate, but that is essentially the same angle that my eye needs in order to see. Then the two tools and my hands will block both the light and my eyesight. 

I have a couple of USB optical inspection cameras, one of which might be useful if I can suspend it to give me the view from a PC screen instead of needing my eyes in place. If I can then work out a light placement that shines around the camera, the remaining issue is tool access and movement. I expect this to be a learning experience as I try different placements for everything. 

Monday, October 16, 2023

Discovered broken mainspring during the Tab and Carrier Return cord work

FOUND ANOTHER METHOD ONLINE AND TRIED IT

The key to this new method is that I don't have to shorten the tab cord with a knot. That dramatically reduces the risk of the cord popping off the pulley as it did before. This method comes from a Phoenix Typewriter YouTube video I just watched.

First step, with all cords disconnected from drums, is to latch in carrier return and hand cycle until the mainspring stops at full tightness. The next step would be to release about seven turns before attaching cords and the rest. 

The mainspring never tightened past a certain point, which indicated that it was broken internally. That explains some of the funky behavior I saw during my prior attempts to attach the cords 

DONOR SELETRIC TO THE RESCUE, AGAIN

The mainspring on the Selectric 1 I bought as a parts donor was in good shape, so I moved it over. I then opened the original mainspring and confirmed that it had broken inside. 

Broken spring

Donor machine replacement

Next session in the workshop I will wind it up then go through the Phoenix Typewriter procedure to try to get my carrier return and tab cords properly installed. Hopefully that will be successful so that I can move on to fixing the excessive tension on the Rotate spring. 

Sunday, October 15, 2023

Drama and defeat in the battle of the tab cord attachment

SURPRISINGLY HARD TO GET THE CORD OVER THE SPRING LOADED PULLEY

When I had attached the tab cord to the drum and the carrier, it only needed to be pulled out around the spring loaded pulley that will maintain tension. The strength of the springs on that pulley don't allow simply pushing the pulley inwards while manipulating the cord. 

I ended up removing the pulley assembly, fitting the cord on it and then twisting it up into place in order to reinsert the screw attaching the assembly to the typewriter. There it was - a set of cords attached and at proper tension. The carrier was about 1/5th of the way to the right, which was the position that allowed me to attach the tab cord, maneuver it to get a second loop around the drum, and attach it all prior to the spring loaded pulley dance. 

THOUGHT I HAD IT, DID CARRIER RETURN TO WIND UP THE MAINSPRING

I latched in a carrier return to pull the carrier to the left edge of the machine and to wind some tension into the mainspring. Everything moved well until I reached the edge and tried to release the carrier return clutch. The machine did not unlatch, it strained pulling the carrier against column 1 and kept turning the tab cord drum so that the end of the cord was barely in the notch with no spare cord. 

POP GOES THE TAB CORD

As I wrestled with the machine trying to get it release the carrier return clutch and stop turning everything the wrong way, I heard a pop and the end of the tab cord came off the drum. Time to start over and try this again. There must be some secret to doing this, but none of the IBM manuals nor the YouTube videos address it, instead presenting the idealized process where it all just fits together and works. 

TAKING A BREAK FROM THE FRUSTRATION BEFORE I DIVE BACK IN

I did some work building my new vacuum tube curve tracer, a project that I originally cobbled together some years ago based on Ronald Dekker's uTracer design. Ronald works at Phillips Research and definitely knows vacuum tubes. This device connects to software on a PC that gives all the curves and results with a very nicely built GUI. 

The uTracer had a weakness in how it drove the filament voltage which was corrected by a clever design from Stephan Lafferty that adds a very accurate filament/heater power supply. I recently completed the heater part of the project and decided to improve the build and esthetics from the quick and dirty version I made years ago.

I cut a new front panel and made a decal labeling the various controls and sockets, unsoldered everything from the old panel and began construction. I lost one of the knobs so I will be replacing all ten of the bottom knobs with a new type of knob, as soon as the order arrives. I installed all the controls and sockets today and began soldering everything up. 

Each of the nine possible pins of a tube socket as well as the cap electrode can be switched to one of six roles - cathode, control grid, screen grid, anode, or either end of the filament supply. That accounts for the ten knobs at the bottom. The rotary knob at the top sets the filament voltage to 5, 6.3 or 12.6V but allows for an external supply if a tube has an unusual heater voltage requirement. 

There are four sockets, for 7 pin and 9 pin miniature tubes, octal tubes and loctal tubes. Pin straighteners are on the panel to ensure that the pins don't bend or snap while being handled. I can make adapters that plug into the octal socket to accommodate rarer tube types including nuvistor as well as the older tubes like a 4 pin radio tube. 



I also did some organizing of the workshop, collecting items into containers and labeling them. This makes the shop neater and more open but also helps me find what I need much faster than the chaos of before.