WAITING FOR PCB AND PARTS TO BUILD SIGNAL DRIVER BOARD
There are seven signals coming from the 1130 that need to be conditioned and driven into the Virtual 2315 Cartridge Facility (V2315CF). A few of them operate in two different ways depending on whether the V2315CF is running in virtual or real mode. In real mode, the signal from the 1130 is electrically connected to the signal wire running out to the IBM 2310 internal disk drive in the 1130 system. Additionally, the V2315CF snoops on that signal so that it can stay in sync or shadow what the 2310 disk is doing. In virtual mode, the 1130 signal only runs to the V2315CF. This produces very different impedance and voltage levels based on the mode.
I designed a Schmitt Trigger circuit to clean up signals coming from the IBM 1130's Solid Logic Technology (SLT) circuitry that has to be detected by the V2315CF. Because of the challenges of impedance matching and ensuring adequate signal swing from an SLT output to a modern 74LVC244 receiver chip as installed on the V2315CF, I chose to put this new circuit in the signal line.
SIGNAL PATH FOR THE V2315CF
Signals run in and out of the IBM 1130's SLT circuits situated in compartment C1 of logic gate A of the system, going over twisted wire pairs in a cable that originally was plugged directly into the SLT circuits in the rear of the 2310 disk drive. The cable is plugged into the 2310 Interface Board of the V2315CF instead of the disk drive.
A cable of twisted wire pairs runs from the SLT circuits of the 2310 disk drive to the 2310 Interface Board. Both the 1130 to 2310 Interface Board cable and the 2310 to 2310 Interface Board cable end with an SLT card connector, which is a 12 row by 2 column female connector.
On the 2310 Interface Board, the signals from both cables are routed to a pair of ribbon cables which carry those signals up to the main unit of the V2315CF. The signals that the V2315CF will read are hooked to a 74LVC244 receiver chip, while the signals coming out of the V215CF are hooked to a SN75451 chip which has open collector outputs. The ribbon cables run to a connector board that plugs into the V2315CF.
All the signals on the ribbon cables have the potential to have termination resistors applied to them. A PCB plugs into the rear of the V2315CF where there are spots for a pullup and a pulldown resistor for each signal line. The pullup goes to +5V and the pulldown is to ground.
On the DEC computers for which George Wiley designed the RK-05 Emulator that I based the V2315CF on, each signal has a 178 ohm pullup and a 383 ohm pulldown, implementing a voltage of about 3.4V when the SN75451 is not conducting and 0V when the open collector is active. The impedance is around 121 ohms since the DEC bus is based on that value.
To match the ribbon cables, however, the impedance should be closer to 100 ohms. Changing the resistors to 169 ohms pullup and 249 ohm pulldown, the impedance is around 100 ohms and the idle voltage is about 3V, which is the nominal logic high voltage for SLT circuits.
The connector board with the ribbon cables that run between the 2310 Interface Board and the V2315CF main unit routes these to the backplane of the V2315CF main unit which has two connectors each with 18 columns and 2 rows, labeled A and B.
There are a few special signals that connect to the 2310 Interface Board which don't come from the 1130 or the 2310 twisted wire cables. These are directly wired to their destinations, but then run over the ribbon cables to the V2315CF main unit.
HANDY POINT TO INTERCEPT SIGNALS ON THE CABLE CONNECTOR BOARD
The connector board for the V2315CF main unit is pretty simple. It has two ribbon cable connectors and the male fingers to plug into the 18x2 backplane connectors A and B. Traces run between ribbon and backplane connectors. It also features holes that allow wires to be soldered to each of the signals, which is a very handy feature I exploit. These holds are close to the fingers of the backplane connectors.
![]() |
| Ribbon cable connector pins are inputs, bottom holes are outputs |
If I cut the trace on the connector board that connects the ribbon cable pin to the backplane finger for a given signal, then I can fit the Signal Driver board into the circuit. Tack soldering a wire to the ribbon cable connector pin for a given signal provides access to the input for a channel of the Signal Driver board. The output of that channel can be soldered into the holes for the signal thus driving that signal into the 74LVC244 circuit of the V2315CF.
The work all takes place on the underside of the connector board. I worked out where to capture the inputs of the seven signals, where to cut their traces on the board and where to solder in the output wires for those signals.
The view above is of the underside of the PCB, produced by viewing the gerber files for the connector board because I don't have the original PCB design files for the board. I numbered the signals assigned to the seven channels of the new Signal Driver board:
- -Write_Data_Clock_L which is the mixed clock and data pulses during a write to the disk
- -Access_10_20_Mil Step determines whether we move the disk arm 1 or 2 steps
- -Access_Rev_Direction determines whether the disk arm moves toward cylinder 0 or 202
- -Access_Go requests that the disk move the arm the amount and direction set above
- -Head_Select choses whether the head accesses the upper or lower surface of the disk platter
- -Read_Gate activates a read operation for a given sector of the disk
- -Write_Gate activates a write operation for a given sector of the disk


No comments:
Post a Comment